Defect-free drying of large fine-particle zirconia compacts prepared by gelcasting method

In this work, drying of bodies prepared by gelcasting fine submicrometre-sized zirconia particles was studied and a drying process for defect-free bodies with large cross-sections was proposed. It was found that the cracking of large bodies could be prevented by reducing the monomer content and using appropriate non-volatile cosolvents. Glycerol and polyethylene glycols with different molecular weights were used as non-volatile cosolvents in aqueous ceramic suspensions. The complex effects of the individual cosolvents on the gelcasting process and, in particular, on the drying step were investigated and explained. The applicability of individual cosolvents for the gelcasting process were discussed and their optimal use was indicated.     

Microstructure and damage evolution of SiCf/PyC/SiC and SiCf/BN/SiC mini-composites: A synchrotron X-ray computed microtomography study

SiC_f/PyC/SiC and SiC_f/BN/SiC mini-composites comprising single tow SiC fibre-reinforced SiC with chemical vapor deposited PyC or BN interface layers are fabricated. The microstructure evolutions of the mini-composite samples as the oxidation temperature increases (oxidation at 1000, 1200, 1400, and 1600?°C in air for 2?h) are observed by scanning electron microscopy, energy dispersive spectrometry, and X-ray diffraction characterization methods. The damage evolution for each component of the as-fabricated SiC_f/SiC composites (SiC fibre, PyC/BN interface, SiC matrix, and mesophase) is mapped as a three-dimensional (3D) image and quantified with X-ray computed tomography. The mechanical performance of the composites is investigated via tensile tests.The results reveal that tensile failure occurs after the delamination and fibre pull-out in the SiC_f/PyC/SiC composites due to the volatilization of the PyC interface at high temperatures in the air environment. Meanwhile, the gaps between the fibres and matrix lead to rapid oxidation and crack propagation from the SiC matrix to SiC fibre, resulting in the failure of the SiC_f/PyC/SiC composites as the oxidation temperature increases to 1600?°C. On the other hand, the oxidation products of B₂O₃ molten compounds (reacted from the BN interface) fill up the fracture, cracks, and voids in the SiC matrix, providing excellent strength retention at elevated oxidation temperatures. Moreover, under the protection of B₂O₃, the SiC_f/BN/SiC mini-composites show a nearly intact microstructure of the SiC fibre, a low void growth rate from the matrix to fibre, and inhibition of new void formation and the SiO₂ grain growth from room to high temperatures. This work provides guidance for predicting the service life of SiC_f/PyC/SiC and SiC_f/BN/SiC composite materials, and is fundamental for establishing multiscale damage models on a local scale.     

古建筑木结构透榫节点力学模型研究

为研究古建筑木结构透榫节点的M-θ力学模型，在分析透榫节点构造特征与受力机理的基础上，建立其数值模型，用透榫节点的试验数据验证了该数值模型的正确性，并分析了节点缝隙、木材横纹弹性模量和大榫头长度对透榫节点受弯承载力的影响。根据受力分析结果，建立以弹性点、屈服点与极限点为特征点的三折线多参数M-θ力学模型，其结果与多数的试验结果基本吻合，并将该力学模型应用于木构架的受力分析。研究结果表明：透榫节点的滞回耗能能力强，节点的变形主要集中在榫头处。当榫头与卯口之间的缝隙增大时，节点的受弯承载力降低。随木材横纹弹性模量的提高和大榫头长度的增加，节点的受弯承载力有一定提高。文章建立的M-θ力学模型能较好反映透榫节点的受力过程，适用于木构架的受力分析，其荷载 位移骨架曲线与试验结果基本吻合。研究成果可为古建筑木结构的维修与保护提供参考。     

Preparation and temperature-resistance characteristics of novel dense SiAlCN ceramics

The compact green bodies, prepared via a novel solid-liquid mixing method of precursors, were successfully pyrolyzed to obtain the dense bulk SiAlCN ceramics at 1000 °C. It can be seen from their SEM that they have uniform and dense microstructure, indicating that this method can be used to prepare bulk ceramics. In order to verify that they can be used as sensor heads, their temperature-resistance characteristics and repeatability were tested. The results show that the conductive mechanism belongs to Arrhenius's Tailed-State and Extended-State in the temperature range of 500–650 °C and 650–930 °C, respectively. And it shows that SiAlCN ceramics can be used as the sensor heads for high-temperature sensors.     

Highly textured and strongly anisotropic TiB2 ceramics prepared using magnetic field alignment (9T)

Highly textured TiB₂ ceramics were prepared by slip casting an aqueous suspension in a magnetic field of 9 T, followed by sintering using Field Assisted Sintering Technology (FAST). Particle size refinement by ball milling improved both the degree of texturing and densification of the material (RD > 98 %). The sintered material exhibited a Lotgering orientation factor of 0.90, with the c-axis of TiB₂ oriented parallel to the magnetic field and FAST pressing direction. The texturing effect induced by the uniaxial pressing was negligible. The textured TiB₂ material exhibited a significant anisotropy in mechanical properties; the values of hardness and indentation elastic modulus measured along directions transverse to the c-axis of TiB₂ were 37 % and 13 % higher than the ones measured along the c-axis direction. Moreover, the specific wear rate of a surface of textured TiB₂ parallel to the field was one order of magnitude lower than a surface perpendicular to the field.     

基于FFT的循环平稳信号波达方向估计

针对在电子对抗实际应用中，来波信号比较集中的情况，提出一种基于FFT的循环平稳信号DOA估计算法。该算法将FFT引入到Extended Cyclic-MUSIC算法中，预先探索存在信号的空间局部区域，避免了全空间谱峰搜索，提高了波达方向检测效率。仿真结果证明了该算法的有效性。     

Thermal emission properties of Al2O3/Er3Al5O12 eutectic ceramics

The mechanical properties and thermal stability of the Al₂O₃/Er₃Al₅O₁₂ (EAG) eutectic ceramics have been investigated at very high temperature. The emissive properties of this eutectic ceramics have also been measured and its possibilities of application to an emitter have been discussed. The present eutectic ceramic has excellent high-temperature strength characteristics, showing that tensile yielding stress is approximately 300 MPa at 1650 °C and superior thermal stability at 1700 °C in an air atmosphere. The present material shows strong selective emission bands at wavelength 1.5 μm due to Er³⁺ ion. The emission bands of this material are nearly coincident with the sensitive region of GaSb PV cell, therefore, the Al₂O₃/EAG eutectic ceramic can be regarded as one of the promising emitter materials in TPV systems.     

The influence of the alloying elements upon the transformation kinetics and morphologies of ferrite plates in alloy steels

A series of Fe-C-X and Fe-C-X₁-X₂ alloys in which X, X₁ and X₂ either raise or depress the activity of C iny were investigated by autodilatometer, optical microscopy, and transmission electron microscopy (TEM) to reveal the relations among the chemical composition, transformation kinetics, and morphology of ferrite plates. The incubation time of austenite decomposition at the nose temperature in the time-temperature-transformation (TTT) diagrams, the concentration of C in y in contact with theα/gg boundary, and the growth rate of ferrite were evaluated to estimate the magnitude of the solute drag-like effect (SDLE) for the different alloying elements used. All the results are consistent qualitatively with the SDLE hypothesis. This article is based on a presentation made at the Pacific Rim Conference on the “Roles of Shear and Diffusion in the Formation of Plate-Shaped Transformation Products,” held December 18-22, 1992, in Kona, Hawaii, under the auspices of ASM INTERNATIONAL’S Phase Transformations Committee.     

配送中心单品拣货模式及其效能分析

紧扣拣货作业的关键目标,介绍了8种低成本的单品拣货模式,并从生产力指标和人员配置两个方面对各种模式的效能进行了计算分析,能为配送中心拣货系统的设计和选择合适的单品拣货模式提供依据.